Direction machine: used to drive the hoop bracket and gun body to move left and right, composed of a screw, a direction screw, a direction nut, a runner, etc. The right end of the pen www.biquge.info screw barrel is sleeved with a liner cylinder, which is installed in the ear hole of the bracket, and is connected with the runner with an external thread and a tapered pin. The screw is screwed with an inner thread, and the screw is covered with a casing and fixed with a pin. One end of the casing is screwed on the direction nut and fixed with a standing screw. The direction nut is screwed on the high and low screw barrels and fixed with a tapered pin. When the runner is rotated, the screw, the casing and the direction nut are fixed, but the screw rotates, and the gun body swings left and right through the hoop bracket, so as to give the gun body the direction of firing.

High and low machine: used to connect the nut of the direction machine and drive the gun body to rise and land, which is composed of high and low machine body, gearbox, large and small bevel gears, rotating handles, screws and screws. The high and low machine body is connected with the left and right frame legs as a whole, which is used to carry the parts of the high and low machine. The screw barrel is sleeved with a sleeve and fixed at the upper end of the high and low body with a screw cover. The lower gearbox is equipped with a large bevel gear, and a rotary handle is installed on the large bevel gear shaft. The high and low screw rod is screwed with the screw barrel, and the lower end is sleeved with a small bevel gear, and is connected with the nut by a taper pin, and is combined at the lower end of the high and low body. When the knob is turned, the large bevel gear drives the small bevel gear and the screw of the high and low machine to rotate in place, and the screw barrel rises and falls in the high and low fuselage, thus giving the gun an angle of fire. Frame leg and level adjustment machine: The right leg tube of the frame leg is provided with a bundle gun belt, and a standing hoe is welded under it. There is a leveling machine on the left leg tube. The leveling machine is composed of slide pipe, adjusting screw, spring, screw ring, set collar, ratchet, set wrench, connecting rod, etc. When in use, pull the set wrench down, and the set clamp is released and slides over the slide tube to adjust the approximate level of the bracket. At this time, rotate the adjusting screw, because of the restriction of the washer, the adjusting screw can only rotate in situ, so that the slide pipe drives the set lock to move up and down, and the high and low body swings through the connecting rod to adjust the precise level of the bracket.

Seat plate: used to withstand the recoil of the mortar when fired, which is composed of a main board, a mortar, a seat plate reinforcement and a gun tail lock. The gun tail lock is used to restrict the gun pestle from falling out of the mortar when recoil and wrenching, and is composed of a handle, a lock body, a lock seat, etc. Flip the handle to lock the pestle in the mortar.

Accessories and quadrants: Accessories include combination wrenches, fuze wrenches, wrenches, oil cans, hanging balls, guns, benchmarks, etc. The gun is also equipped with a quadrant to check and assign a mortar angle of fire.

Ammunition type:

Anti-personnel grenade: the length of the whole bomb is 234-241mm, the mass of the whole bomb is 1.33kg, and the tail of 10 pieces is used. The body is made of rare earth cast iron, and it is filled with 0.11kg of naphthalene - 80 explosives or 0.13kg of black - 27 stone explosives. The number is 0-3, the basic ****** mass is 3.3g, the mass of a single additional propellant package is 2.9g, and the total mass of the whole ****** is 12g. The muzzle velocity is 65m/s when it is launched with No. 0 equipment, and the muzzle velocity is 134m/s when it is equipped with No. 3 ******, the maximum chamber pressure is 26MPa, and the effective killing radius of shrapnel is 10.2m.

There are two main types of anti-personnel grenades: one has three ring grooves on the tail pipe to jam the ring-shaped additional medicine bag; The other type has a loopless groove, and the additional propellant pack is directly attached to the tail pipe.

Anti-personnel grenades are equipped with "force-1A fuses" and "force-3 fuzes" (also known as 100-3 fuzes, mainly used on Type 31 anti-personnel grenades).

The process of action of the "1A-type fuse" is as follows: Remove the safety pin and remove the protective cap before firing. When the shell moves in the body tube after being fired, the inertia cylinder equipped with the firing pin, the service safety steel ball, the safety steel ball and the inertia cylinder spring moves downward relative to the fuze body, and the service safety steel ball is released after the movement is in place. When approaching the muzzle, the inertia cylinder rises under the action of the inertia cylinder spring, driving the firing pin to move upward, and the **** seat located on the side of the firing pin moves to the center line of the cannonball under the action of the **** seat spring, and hits the tip of the needle positively. After the cannon ejects the muzzle LM, the safety steel ball is detached, and the shell hits the ground and stabs the ****, detonating the shell.

The action process of the force-3 fuze is as follows: the safety cap is removed before firing, and the maximum linear acceleration inertia of the shell in the body tube is only 270 N, which is less than the minimum resistance of the shut-off pin (the resistance of the shut-off pin is 320-420 N), so the bow i letter does not move in the body tube.

When the target reaction force is far greater than the maximum resistance of the cutting pin, the top cap and firing pin move backwards, the firing needle pierces the fire cap, and the fire cap detonates the ****, thereby detonating the shell.

It can be seen from this that a pursuit artillery shell equipped with a "force-3 fuse" can be used as a grenade as long as the safety cap is removed.

60mm mortar long projectile: The projectile is composed of a fuse, a mouth snail, a centering wing, an explosive, a projectile body, a cartridge belt, a tail pipe, a tail fin, etc. The length of the whole bomb is 741-755mm; The mass of the whole bomb is 3.35kg, the body of the bomb is made of steel pipe, the internal ******* explosives are 0.65kg, the number of ****** is 0-3, the basic ****** mass is 10g, the mass of a single additional charge package is 3.7g, and the total mass of ****** is 21.2g;

Maximum muzzle velocity 93m/s: maximum chamber pressure 21MPa: maximum range 752m; Radius of destruction: 18. 4m, with force-2, eye-6 fuze.

60mm mortar 120 grenade: It consists of a 120 grenade warhead screwed on a 60mm mortar long projectile boom. The length of the total bomb is 912-928mm; The mass of the whole bomb is 6.59kg, the body of the bullet is made of rolled steel plate, filled with 2.45kg of explosives, and the maximum muzzle velocity is 65m/s; Maximum firing range 420m; The radius of destruction is 21.6m. The warhead of the bomb consists of a moisture-proof plug, a mouth snail, an explosive, a projectile body and a bottom bracket.

Of course, these artillery technologies are much more advanced than rifle technology, and they are also more jumpy, and all the civilization proving grounds are provided to the orc empire and the dwarven empire just technology!

The Orc Empire and the Dwarven Empire want to mass-produce the technology of these artillery, but it will not be as simple as that Orc Whip Rifle!

Although the structure of the orc whip rifle looks quite complicated, there are already a lot of basic orc empires and dwarf empires in the field of rifles, and it is not difficult to manufacture mass production lines, but!

These cannons can be said to have completely subverted the concept of smoothbore cannons, and it can be said that they have formed a very obvious technological generation gap with the artillery base of the Orc Empire and the Dwarf Empire!

Even if the weapons engineers of the Orc Empire and the Dwarven Empire want to build this kind of cannon according to the gourd drawing, it will take a lot of time!

The Orc Emperor naturally knew this, so he didn't force the Weapons Research Institute to come up with this kind of artillery technology in a short period of time!

If Li Liguo knew that the artillery technology of the Orc Empire and the Dwarf Empire had reached the level of the World War II era in his previous life, he would definitely have a headache! (To be continued.) )