"The metal smelted from this ore is soft, dense and hard, much lower than the standard of available steel. Moreover, the source energy guidance it presents is very poor, it needs to stimulate pressure, cumbersome and complicated, and few people pay attention to this ore. Lucia stayed in the moonlight for a moment, feeling less irritable, and re-raised her glass, and walked back into the room. "If you're interested in this kind of thing, there's a sample in the workshop to give it a try. ”

Lucia's eyes were a little misty, and she walked inside, raised her right hand, and gently shook her hand goodbye.

Soft, low hardness, and the need to excite pressure to generate source energy guidance means that in normal conditions, this kind of thing has the effect of source energy confinement...... Gustav looked at the crystal in his hand and was stunned.

Wait a minute...... In a binary-centered world, there are two states, 0 and 1, which correspond to open and closed, yes or no.

This is the fundamental basis of the computer, the idea of wanting to describe things in terms of whether there are two states or not.

"If this soft metal also has this property, it means ...... If it is not activated, it exhibits the Forbidden trait, which can be used as a sign of 'No' or 'Fail'. In the excited state, it exhibits the nature of a conductor of source energy, which can be used as a manifestation of 'is' or 'pass'. ”

Gustav's heart pounded, and he faintly grasped a great idea.

Lucia said that there was a purified product of this metal on display in the etching room!

Hurriedly raising his glass, Gustav ran into the scene of the dinner.

Because of Lucia's invitation just now, some people let out ambiguous boos. Putting down his glass, Gustav walked up to Lucia: "I'm sorry, Miss Lucia, and Mr. Lento, I have some ideas and want to go back to the etching room now. Miss Lucia, can you lend me the key to the etching room?"

The latter, with some confusion, took the key from his neck and handed it out, and Gustav took it very quickly and ran out without looking back.

Did he have a new idea?, thinking suspiciously, Lucia continued to preside over the buffet.

............

Sheet metal from the Lem mine...... Gustav quickly searched the sample room.

Every aspiring enchantment workshop has a sample room where a large number of metal samples are stored to study how to perform better enchantment etching.

After searching for a long time, Gustav finally found one such piece of metal in the corner of the sample room. As Lucia said, the metal is really soft, not as hard as steel or voicalsteel.

Turning to the etching room, Gustav opened his workbench and placed the metal sample on it.

The first thing to confirm is what is the threshold at which the energy conductivity of the metal source is excited!

In the world of Source Energy, a standard unit of source pressure is called 'El', named in honor of the Grand Arcanist who proposed and defined this unit. Generally speaking, the arcane models before level 5 vary from one Elt to several hundred Ells depending on their role.

Gustav turned on the gun and turned off the corrosive light part, so that the gun became a device that sprayed the source energy pressure alone.

First of all, start with the pressure of 0.1 El, and adjust upwards......

Little by little, Gustav began to experiment, using a spray gun to start slicing across the Lem metal sheets.

The pressure of 0.1 El is not abnormal, and the whole piece of metal is very stable...... This indicates that the excitation pressure of the Lem mine is still above this unit.

Continuing to test downwards, Gustav increased the pressure from one elt upwards to the point of zero sixths of an elt, and the whole metal remained very stable.

It's about to be adjusted to 0.7 El......

It was at this time that Gustav increased the source pressure of the spray gun to 0.7 el, and finally saw a different effect.

With the change of the spray gun spray position, the surface of the Lime Mine began to change color, and the slightly purple source energy began to gather at the spray place, which indicates that this part of the Lime Mine has produced the nature of conducting the source energy, and it is no longer in a forbidden state.

Is the threshold 0.7 el? Gustav took out a pen and paper from the side and began to record the situation tonight.

"Lem mine, soft, density 2.58, under normal conditions in a forbidden state, when the excitation threshold reaches 0.7 Er, Lem metal begins to appear in a state of source energy conduction. ”

Gustav had a vague idea.

Now, whether it is the classicist or the neo-modernist etching idea, it is basically to complete the corrosion on the originally intact source energy layer through corrosive light, resulting in a forbidden state. As a result, the attachment of the arcane model is formed, and at the time of excitation, due to the difference in source energy density, the source energy that enters the forbidden area is converted into arcane through the model, thus being released.

The key to everything is how to create the 'Forbidden Zone'.

However, this Lem Mine, which is itself forbidden to demons, only exhibits pathway changes under threshold pressure.

If, if...... Gustav organized his own ideas.

If each layer of arcane models is compared to a drawing, then the part of the picture that has a pattern corresponds to the enchantment work as the 'forbidden area'. The part that does not have a pattern corresponds to the 'path' area for the enchantment job.

"If you want to draw a certain layer of the arcane model using the Rem Mine as a template, then as long as all the areas outside the pattern part are set to 'pathways', naturally, the rest of the area will be closed in the 'forbidden area'. ”

Gustav's heart pounded, he knew he had grabbed something, and a light was about to come out of his mind.

Why do you have to etch arcane models on your equipment, why not replace the cumbersome etching with a unified arcane model generator, why does an etching piece of equipment have to be limited to enchanting only one type of arcane, why does the neo-modernist have to work better than the classical school etching?

At present, the etching processing process, because it is a manual operation, the accuracy can barely reach the level of one-tenth of a millimeter. But if everything can be carried out according to industrial standards, it can reach the micron level or even the nano level in the future!

His eyes were getting brighter, and looking at the Lem mine in his hand, Gustav knew he had found a research topic that might serve as a future direction.

I'm going to give it a try, I'm going to replace the repetitive meaningless etching with this Lem mine, and I'm going to raise the standard of craftsmanship in the enchanting industry even more!