With the online measurement tooling that had just been added and the tooling schedule in his hand, Li Xiang began to distribute one process at a time. Pen, fun, and www.biquge.info

Li Xiang not only has to deliver these tooling to the hands of the operators of each process, but also instructs and teaches them how to use them.

The first tooling is used to measure the distance from the center of the cylinder bore of the body to the side of the body positioning, and this size can not be measured by the existing measuring tools on site, such as: vernier calipers, etc., in any case.

The requirements of this size are not very strict, the tolerance requirements are 0.1mm, therefore, Li Xiang's design is very ingenious, based on the positioning side, and a hole of the size of a cylinder hole is cut out on a flat plate, as long as the hole can be consistent with the cylinder hole, then there is no big problem with this size.

The operator on the side of the positioning of the milling machine body is called Zhang Zhengbao, who is concentrating on his work at this time, Li Xiang walked to his side and took out the cylinder bore measurement tool.

Zhang Zhengbao saw Li Xiang and asked, "Li Gong, what did you bring here?" ”

Li Xiang smiled slightly, did not immediately answer Zhang Zhengbao's question, but took the cylinder bore measurement tooling and came to the side of Zhang Zhengbao's machined body.

Along the positioning side of the body, Li Xiang stuck the cylinder bore measurement tooling on the fuselage, and detected the cylinder bore one by one.

Zhang Zhengbao looked at Li Xiang's movements, a little puzzled, a little worried, and thought that there was a mistake in the work he was doing, and asked cautiously: "Li Gong, what are you busy with?" I'm fine, right? ”

Li Xiang used the cylinder bore measuring tooling to measure the position of the center of the cylinder bore of a machine body, which indeed met the requirements, and immediately smiled and said: "No problem, you are doing a good job, you see this thing in my hand, it is the tooling used to measure the distance from the center of the cylinder bore to the side, you take it." ”

Li Xiang handed the cylinder bore measurement tooling to Zhang Zhengbao's hand and continued: "In the future, with this cylinder bore measurement tool, you can check the body you process, and you don't have to worry about waiting for the three-coordinate measurement results." ”

Zhang Zhengbao was overjoyed, hurriedly took over the measuring tool, and measured several bodies in a row according to Li Xiang's operation method just now, and then walked up to Li Xiang and said: "Li Gong, this is really good, with this measurement tool, it is much more convenient than sending three coordinates." ”

Li Xiang nodded and said: "Okay, when you work in the future, you will use this measuring tooling to check every five pieces or every ten pieces, so as to ensure that there will be no batch of unqualified products." ”

Zhang Zhengbao nodded, put away the tooling and put it away.

"Okay, you hurry up and get to work, I have to send other tooling to other processes."

After Li Xiang finished speaking, he picked up the box with the online measurement fixture and walked towards the back process.

The next tooling is to measure the distance to the bottom of the Φ12 main oil channel hole, the data of this distance is large, and the range of the general vernier caliper is simply not enough; Moreover, when the machine body is processed to this process, the bottom surface is facing down, which makes this size more difficult to measure.

When he came to the oil channel hole processing process, Li Xiang put down the box and shouted to the operator Zhao Binbin: "Binbin, come here, I'll tell you something." ”

Zhao Binbin, the operator of the oil duct hole process, is younger than Li Xiang, and is reading a novel on his mobile phone next to the toolbox.

Originally, it was absolutely forbidden to play with mobile phones at work, but Li Xiang had just worked for a few days, and he was responsible for the technical process, and the employees in these workshops did not avoid Li Xiang in terms of labor discipline.

Li Xiang doesn't care about these, his main task at present is to straighten out all the process and technical work in the workshop, these labor discipline problems, hum, the future is long!

was disturbed to read the novel, Zhao Binbin was a little impatient, but when he looked up and saw that it was Li Xiang, he didn't say anything, and walked towards Li Xiang, after all, he has a lot of work here, and he is still assessed by craftsmen like Li Xiang.

"What's the matter, Li Gong?" Zhao Binbin asked, "If there is nothing too important, I still have to work." ”

Li Xiang listened, frowned slightly, and snorted coldly in his heart, you obviously read the novel there, didn't I see it?

However, Li Xiang doesn't bother with him, each of these operators has a different personality, if they are comprehensive, then Li Xiang will not be exhausted, as long as they don't go too far, Li Xiang will open one eye and close one eye.

"I'll make you a measuring fixture." Li Xiang said, took out the position measurement tooling of the main oil duct hole, "Let's try it and see if it's good to use." ”

However, Zhao Binbin didn't pick it up, but glanced at the tooling that Li Xiang took out, and said nonchalantly: "Li Gong, there's no need, the tolerance between the main oil channel hole and the bottom surface size is twenty wires, even if it's super poor, it doesn't matter, and get a tooling to measure, how troublesome it is!" ”

Li Xiang snorted lightly and said: "Yes, the requirements are not high, but it is very important, once the deviation is serious, or after the post-process tolerance superposition, it is likely that the requirements will not be met in the end, and the oil channel hole will not meet the requirements at all, then the lubrication system of the entire engine will be affected, and the scrapped will not be a body blank, but the entire engine, and the value will be great." ”

Zhao Binbin saw that Li Xiang was a little angry, and what Li Xiang said was also conclusive, if there was really a scrapped engine, it was not for him to be responsible for as an operator.

After taking over the measurement tool, Zhao Binbin asked, "How do you use this thing?" ”

Li Xiang shook his head, took the measuring tooling again, came to the side of a machine body that had processed the main oil channel hole, and said: "You have a good look, I will show you a demonstration, and this will be included in the process discipline inspection in the future." ”

Process discipline inspection, refers to the front-line operators in the usual work of a variety of data records, the implementation of standard operations, a kind of inspection, if the problem is found, not only to deduct the corresponding team points, and even deduct the responsible person's money, which is also the reason why Zhao Binbin has a taboo on Li Xiang.

For people like Zhao Binbin, he can only be urged to work hard in this way, otherwise he will definitely not carry it out.

After demonstrating to Zhao Binbin, and making sure that he understood, Li Xiang left the process of processing oil duct holes with the box and continued to distribute the tooling.

Finally, before getting off work, Li Xiang distributed more than a dozen measuring fixtures of all sizes to the hands of the operators, and personally demonstrated the operation methods to them.

Back in the office, most of the people were sitting at their desks, waiting for the end of work, Li Xiang sighed softly and walked towards Su Qicai.

Now the situation of the whole Daxuan power is actually very unoptimistic, but most of them are still immersed in the previous glory and are unwilling to admit this fact.

Li Xiang is helpless, he is just a small craftsman now, and he can't change anything. Li Xiang can only do his best and do his part.

PS: I'm going to work tomorrow!! It's snowing today!! My broken electric car!! Ask for recommendation and collection ~~~