The gearbox level of Nanshan has been seen by everyone in the industry.

So even if the 4MT, 6MT and 4AT were on display, no one would be particularly impressed.

After all, there is already a case of 6AT put there.

However, the launch of the Nanshan 1.5T turbocharged engine has caused a very big impact.

"Mr. Wang, I heard that this engine was specially researched by Nanshan for BYD's new car."

"Although I am not sure what BYD's new model will look like, if there is such an engine with very good power performance, coupled with the Nanshan gearbox, I am afraid it will have a very big impact on the market at that time."

"I think that in the future, Great Wall Motor's engines will continue to be purchased from Aerospace Mitsubishi and Dongan Power, or whether they will speed up their own research progress, and we need to think again."

Almost all of Zhu Jianbo's attention today is on the engine.

Until now, Great Wall Motor's shortcomings have been in the engine.

Even all domestic independent brands, engines are shortcomings.

Although this shortcoming can basically be broken through in all aspects in the next 10 years, it is not good in 2003.

In a group of weak chickens, a Tyrannosaurus rex was suddenly discovered, and the impact on everyone must have been very big.

"The research institute and the purchasing department contacted Nanshan together to find them to ask for the specific parameters and prototype of this engine, and our new models can also consider using this product."

"Fuel consumption is lower, power is stronger, and as long as there is no problem with quality, there is no reason why we should not use it."

"Of course, we also have to speed up the research of the engine, Nanshan can produce it, and there is no reason why we can't produce it."

"We can even discuss with Nanshan to purchase a certain number of Nanshan engines and then ask them to give us technical licensing."

"It would be much easier to study the engine on this basis."

Wang Ying did not hesitate to give a conclusion.

There are good things, and there's no reason not to use them.

"It's a bit difficult to estimate, they sell engines, and the business can go on forever."

"But if we directly license our technology, even if the cost of licensing is relatively high, even if we directly buy their engine technology, it will be a matter of one or two hundred million at most."

"But then there will be no business."

"If the water flows for a long time, even if an engine only earns 1,000 yuan, as long as 100,000 units are produced, there will be a profit of 100 million."

"According to the current development of the automobile market, we can basically consume 100,000 units a year."

Zhu Jianbo felt that if he was Nanshan, he would definitely not sell the engine technology he had just researched.

Even if a series of restrictions are given, they are reluctant to sell.

However, Wang Ying didn't completely look at it himself, and said: "There is no harm in giving it a try, what if people agree?" ”

……

"Section Chief Fang, just introduced by the people in Nanshan, the price of their die steel is only 200,000 tons, which is almost half cheaper than the SKD11 imported by Dongying."

"Can your mold department consider verifying whether Nanshan Special Steel can meet our quality requirements?"

Liu Wei, the head of the purchasing department of Xifeng Die Chong, also came to Yangcheng to participate in Nanshan Science and Technology Day with Fang Wei, the head of the mold section, and others.

For them, they already have a good understanding of press and mold technology.

The two sides have also cooperated so far.

But in terms of die steel, it is the place they pay the most attention to today.

As a stamping manufacturer, press equipment and molds are the two most important pieces of hardware.

Among them, in terms of press equipment, each stamping plant is generally outsourced, and it is difficult to reflect its core competitiveness.

Then it depends on the mold involved.

Except for PRG molds and TDM molds, most of which are purchased from Nanshan, and other TDM molds are produced by Xifeng Die Chong's own mold workshop.

In this case, the procurement of various special steels is naturally an inevitable thing in the process of making molds.

In the past, they have not tried to use die steel from domestic manufacturers such as Baosteel.

It can barely be used on some parts with low difficulty requirements and low precision requirements.

However, in the stamping process of high-strength steel plates, domestic die steel cannot meet the requirements.

Whether it is the stamping life of the die or the possibility of problems in the production process, everyone is not at the same level.

This is basically a common situation faced by domestic stamping manufacturers.

"Judging from the current die steel parameters they provide, there is no problem at all, and it is no worse than the imported SKD11."

"In the next step, we will first buy a small batch of Nanshan's mold steel, do some material testing, and also try to use it to make several sets of molds."

"If there is no problem, it is natural to switch to Nanshan's die steel, so that our mold cost can be reduced by at least one percent."

When Fang Wei left Nanshan, he was specially talked.

He is now thinking that after three years have passed, he will find a way to return to Nanshan.

Especially seeing the thriving situation in Nanshan, he wants to come back as soon as possible.

Besides, even if there is no reason for this, simply in order to reduce costs, he also supports the use of Nanshan special steel.

The premise, of course, is that the material meets the requirements.

"In the past, the group always came to assess our localization rate and asked us whether the Xifeng die punch had achieved 100% localization."

"I didn't have much confidence before, but now even die steel can be domestically produced, and our press is also domestic."

"Then when the group asks us again in the future, we can confidently say that the West Wind Die Punch has achieved 100% localization."

Liu Wei said this, Fang Wei wanted to add, saying that some standard parts on the mold were still imported.

It is still very difficult to truly make 100% localization.

After all, after digging deeper, is the iron ore used in the first phase of your special steel imported?

……

"Mr. Cao, someone from Huaxia Station is here."

When Cao Yang sent Liu Tianwu away and was about to chat with the general managers of some other customers, Mi Ying quickly came over to report the new situation.

On this Nanshan Science and Technology Day, Cao Yang just asked the sales department to invite various customers and potential customers.

For all kinds of media, there is really no special invitation.

After all, these technologies are all TO B, and they don't need the help of the media to publicize them too much, and they will not affect Nanshan's business expansion.

Unexpectedly, in this case, Huaxia TV is also interested?

Could it be that the threshold for going to Huaxia has become so low?

"Let's go over and have a look!"

In any case, Huaxia Terrace's face is definitely to be given.

Cao Yang was going to go over to receive him in person.

(End of chapter)